The Story
Rear Stabilizer Bar Bushing Kit for Lancer
Delphi TD2017W is a rear suspension stabilizer bar bushing kit built with rubber construction and standard replacement dimensions for select Mitsubishi applications. It is engineered for the 2008-2015 Mitsubishi Lancer, rear, and is backed by Delphi’s OE-focused dimensional and material analysis.
Key Features
- Rubber stabilizer bar bushings in black finish
- Two-bushing kit for the rear position
- Standard replacement grade for OE-style service
- Inside diameter: 19.20 mm; outside diameter: 43.30 mm
- Dimensions: 36.60 mm length, 43.30 mm width, 48.60 mm height
- No grease fitting, bracket, or mounting hardware included
Detailed Description
Delphi TD2017W is a suspension stabilizer bar bushing kit for rear service on the 2008-2015 Mitsubishi Lancer. The rubber bushing design helps restore proper stabilizer bar support and fitment where worn bushings can affect suspension feel and noise. Delphi applies OE-level dimensional and material analysis to support accurate replacement fit, and the part is tested across extreme temperatures and salt-spray exposure to verify durability in demanding conditions. This part cross-references Mevotech Supreme MS80893 for the same application.
What It Helps Address
- Rear suspension clunking from worn stabilizer bar bushings
- Excess stabilizer bar movement at the rear axle
- Loose or inconsistent rear-end handling feel
- Noise caused by deteriorated rubber bushings
- Replacement needs on a Mitsubishi Lancer rear stabilizer bar service
Installation Notes and Tips
Verify rear stabilizer bar diameter and bushing dimensions before installation. Inspect the stabilizer bar, brackets, and surrounding suspension components for wear or corrosion before reassembly. Because mounting hardware is not included, reuse or source the required fasteners separately as needed. Confirm fitment for 2008-2015 Mitsubishi Lancer, rear, and compare the old bushing dimensions to Delphi TD2017W before service.
Quality Assurance
Delphi uses OE-focused testing and material analysis for aftermarket steering and suspension components. This bushing kit is evaluated for temperature extremes below -40 degrees C and above 120 degrees C, along with extended salt-spray exposure, to support consistent performance in real-world conditions.
Description
Rear Stabilizer Bar Bushing Kit for Lancer
Delphi TD2017W is a rear suspension stabilizer bar bushing kit built with rubber construction and standard replacement dimensions for select Mitsubishi applications. It is engineered for the 2008-2015 Mitsubishi Lancer, rear, and is backed by Delphi’s OE-focused dimensional and material analysis.
Key Features
- Rubber stabilizer bar bushings in black finish
- Two-bushing kit for the rear position
- Standard replacement grade for OE-style service
- Inside diameter: 19.20 mm; outside diameter: 43.30 mm
- Dimensions: 36.60 mm length, 43.30 mm width, 48.60 mm height
- No grease fitting, bracket, or mounting hardware included
Detailed Description
Delphi TD2017W is a suspension stabilizer bar bushing kit for rear service on the 2008-2015 Mitsubishi Lancer. The rubber bushing design helps restore proper stabilizer bar support and fitment where worn bushings can affect suspension feel and noise. Delphi applies OE-level dimensional and material analysis to support accurate replacement fit, and the part is tested across extreme temperatures and salt-spray exposure to verify durability in demanding conditions. This part cross-references Mevotech Supreme MS80893 for the same application.
What It Helps Address
- Rear suspension clunking from worn stabilizer bar bushings
- Excess stabilizer bar movement at the rear axle
- Loose or inconsistent rear-end handling feel
- Noise caused by deteriorated rubber bushings
- Replacement needs on a Mitsubishi Lancer rear stabilizer bar service
Installation Notes and Tips
Verify rear stabilizer bar diameter and bushing dimensions before installation. Inspect the stabilizer bar, brackets, and surrounding suspension components for wear or corrosion before reassembly. Because mounting hardware is not included, reuse or source the required fasteners separately as needed. Confirm fitment for 2008-2015 Mitsubishi Lancer, rear, and compare the old bushing dimensions to Delphi TD2017W before service.
Quality Assurance
Delphi uses OE-focused testing and material analysis for aftermarket steering and suspension components. This bushing kit is evaluated for temperature extremes below -40 degrees C and above 120 degrees C, along with extended salt-spray exposure, to support consistent performance in real-world conditions.
