The Story
Front Vented Brake Rotor for Ford F-250
The Dynamite Friction DFC Brake Rotor 600-54098 is a front disc brake rotor built for 1973-1979 Ford F-250 trucks with 1-piston calipers. It features a vented design, 321 mm outside diameter, and 30.1 mm nominal thickness to match the specified brake setup.
Key Features
- Part number: 600-54098
- Brand line: DFC Brake Rotor
- Front disc brake rotor for Ford F-250 applications
- Vented rotor construction for front brake service
- Outside diameter: 321 mm
- Nominal thickness: 30.1 mm
- Discard thickness: 28.45 mm
- Inside diameter: 117 mm
- 8-bolt hole design with 1/2-20 bolt hole diameter
- Height: 147.9 mm
Product Details
The DFC Brake Rotor line from Dynamite Friction focuses on direct-fit brake rotor replacement parts with application-specific dimensions. This rotor is specified for the front position on 1973-1979 Ford F-250 models and is matched to 1-piston calipers. The vented rotor design helps support heat management during repeated braking, while the listed thickness and diameter measurements provide the dimensional reference needed for proper brake service. Part number 600-54098 is the identifier to use when verifying the correct front rotor for this Ford truck application.
Common Reasons to Replace
- Brake pulsation or rotor runout during stopping
- Reduced braking performance from worn rotor surfaces
- Rotor thickness approaching discard specification
- Heat-related brake fade from an aging front rotor
- Noise or scoring caused by rotor wear
Installation Notes
Confirm the vehicle is a 1973-1979 Ford F-250 with 1-piston calipers before ordering. Verify rotor dimensions, bolt pattern, and hub fitment against the existing brake assembly, and inspect pads, calipers, and wheel bearings during service. This rotor is for the front position only. Part number 600-54098 should be matched to the vehicle’s brake configuration before installation.
Quality Assurance
Dynamite Friction’s DFC Brake Rotor line is built around application-specific brake rotor specifications for accurate replacement selection. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Description
Front Vented Brake Rotor for Ford F-250
The Dynamite Friction DFC Brake Rotor 600-54098 is a front disc brake rotor built for 1973-1979 Ford F-250 trucks with 1-piston calipers. It features a vented design, 321 mm outside diameter, and 30.1 mm nominal thickness to match the specified brake setup.
Key Features
- Part number: 600-54098
- Brand line: DFC Brake Rotor
- Front disc brake rotor for Ford F-250 applications
- Vented rotor construction for front brake service
- Outside diameter: 321 mm
- Nominal thickness: 30.1 mm
- Discard thickness: 28.45 mm
- Inside diameter: 117 mm
- 8-bolt hole design with 1/2-20 bolt hole diameter
- Height: 147.9 mm
Product Details
The DFC Brake Rotor line from Dynamite Friction focuses on direct-fit brake rotor replacement parts with application-specific dimensions. This rotor is specified for the front position on 1973-1979 Ford F-250 models and is matched to 1-piston calipers. The vented rotor design helps support heat management during repeated braking, while the listed thickness and diameter measurements provide the dimensional reference needed for proper brake service. Part number 600-54098 is the identifier to use when verifying the correct front rotor for this Ford truck application.
Common Reasons to Replace
- Brake pulsation or rotor runout during stopping
- Reduced braking performance from worn rotor surfaces
- Rotor thickness approaching discard specification
- Heat-related brake fade from an aging front rotor
- Noise or scoring caused by rotor wear
Installation Notes
Confirm the vehicle is a 1973-1979 Ford F-250 with 1-piston calipers before ordering. Verify rotor dimensions, bolt pattern, and hub fitment against the existing brake assembly, and inspect pads, calipers, and wheel bearings during service. This rotor is for the front position only. Part number 600-54098 should be matched to the vehicle’s brake configuration before installation.
Quality Assurance
Dynamite Friction’s DFC Brake Rotor line is built around application-specific brake rotor specifications for accurate replacement selection. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
