Original: $109.14
-65%$109.14
$38.20The Story
Rear Right Drilled and Slotted Rotor
The Dynamite Friction DFC Geoperformance Rotor - Drilled and Slotted, part number 830-32010R, is a rear right disc brake rotor built for specific Mini applications. It features a slotted X drilled surface, a 280 mm outside diameter, and a rust resistant coating for added protection in service.
- Part number: 830-32010R
- Rear right disc brake rotor
- Slotted X drilled surface type
- Directional brake surface
- Solid rotor construction
- Outside diameter: 280 mm
- Nominal thickness: 10 mm
- Discard thickness: 8.4 mm
- Bolt circle diameter: 120 mm
- 5-lug / 5-bolt hole design
- Geospec Silver Grey hat finish
- Rust resistant coating: Yes
DFC Geoperformance Rotor Line
The DFC Geoperformance Rotor line focuses on drilled and slotted brake rotor construction for consistent braking performance and a clean, application-specific fit. On this Mini Cooper Countryman and Mini Cooper Paceman rear right application, the 830-32010R uses a directional braking surface and plain disc finish with a coated hat for corrosion resistance.
Vehicle Fitment
- Fits 2011-2016 Mini Cooper Countryman, rear right.
- Fits 2013-2016 Mini Cooper Paceman, rear right.
What This Rotor Helps Address
- Brake pulsation from a worn rear rotor surface
- Reduced braking consistency from rotor wear
- Surface corrosion on the rotor hat and exposed areas
- Uneven rear brake contact on the affected side
- Noise caused by an out-of-spec or damaged rotor
Installation Notes and Tips
Confirm rear right placement before installation. Verify rotor dimensions, bolt circle diameter, center hole diameter, and lug hole size against the existing brake setup on the Mini Cooper Countryman or Mini Cooper Paceman. Inspect pads, caliper condition, and hub surface before installing part number 830-32010R.
Quality Assurance
Dynamite Friction supplies this rotor with a rust resistant coating and Geospec Silver Grey hat finish for added surface protection. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
Description
Rear Right Drilled and Slotted Rotor
The Dynamite Friction DFC Geoperformance Rotor - Drilled and Slotted, part number 830-32010R, is a rear right disc brake rotor built for specific Mini applications. It features a slotted X drilled surface, a 280 mm outside diameter, and a rust resistant coating for added protection in service.
- Part number: 830-32010R
- Rear right disc brake rotor
- Slotted X drilled surface type
- Directional brake surface
- Solid rotor construction
- Outside diameter: 280 mm
- Nominal thickness: 10 mm
- Discard thickness: 8.4 mm
- Bolt circle diameter: 120 mm
- 5-lug / 5-bolt hole design
- Geospec Silver Grey hat finish
- Rust resistant coating: Yes
DFC Geoperformance Rotor Line
The DFC Geoperformance Rotor line focuses on drilled and slotted brake rotor construction for consistent braking performance and a clean, application-specific fit. On this Mini Cooper Countryman and Mini Cooper Paceman rear right application, the 830-32010R uses a directional braking surface and plain disc finish with a coated hat for corrosion resistance.
Vehicle Fitment
- Fits 2011-2016 Mini Cooper Countryman, rear right.
- Fits 2013-2016 Mini Cooper Paceman, rear right.
What This Rotor Helps Address
- Brake pulsation from a worn rear rotor surface
- Reduced braking consistency from rotor wear
- Surface corrosion on the rotor hat and exposed areas
- Uneven rear brake contact on the affected side
- Noise caused by an out-of-spec or damaged rotor
Installation Notes and Tips
Confirm rear right placement before installation. Verify rotor dimensions, bolt circle diameter, center hole diameter, and lug hole size against the existing brake setup on the Mini Cooper Countryman or Mini Cooper Paceman. Inspect pads, caliper condition, and hub surface before installing part number 830-32010R.
Quality Assurance
Dynamite Friction supplies this rotor with a rust resistant coating and Geospec Silver Grey hat finish for added surface protection. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.
